Earthing and Bonding Products
Earthing and bonding are an integral part of any modern electrical protection system design. ERICO offers the best range of long lasting and cost-effective earthing and bonding products available.
For instance, the ERITECH copper-bonded ground rod will bend without tears, cracks or folds, to the outer sheath which will significantly increase its serviceable life and maintain the integrity of the entire electrode as opposed to cheaper ground rods. To enhance the soil conductivity in areas where soil resistivity is high, ERICO’s Ground Enhancement Material (GEM) is a superior product. Once in its set form, maintains constant resistance for the life of the ground system. It performs in all soil conditions even during dry spells and is permanent – i.e. does not dissolve, shrink, decompose or leach out with time.
Besides the above, West Australian Power Protection (WAPP) offers all other earthing and bonding products such as clamps, earth cables, copper tape, earth pits, earth mesh and much more for your earthing needs. Please call WAPP on 08 9451 2199 if you would like us to estimate the amount of GEM required for an installation and also resistivity values for common GEM application.
Ground Enhancement Material (GEM) from ERICO is a superior conductive material that solves your toughest grounding problems. Third-party testing has been completed to verify that GEM conforms to IEC 62561-7. […]
The Mesh Bonding Network Connectors (MBNC) from ERICO allow for fast, simple and economical field connection of grounding and bonding wires. In addition to cross-wire bonding connections, the MBNC can […]
A Cable Runway Ground Strap bonds cable tray, wire mesh tray and cable runway components together and to the telecommunications grounding and bonding infrastructure (e.g., through cabinets and racks). This […]
The requirements for bonding and grounding permanently installed indoor and outdoor swimming pools are provided in Article 680 “Swimming Pools, Fountains and Similar Installations” of the 2005 Edition of the […]
The Common Bonding Network (CBN) Jumper, part of the ERITECH® line of facility electrical protection products, helps achieve a secure electrical connection in the telecommunications grounding and bonding infrastructure. A […]
ERICO Signal Reference Grids (SRG’s) provide a low impedance equipotential plane to protect sensitive electronic equipment from transients. Because typical signal voltages are quite low, equipment can be very sensitive […]
The EGP100 copper grounding plate, part of the ERITECH® line of Facility Electrical Protection products from ERICO, is installed on the base of a wooden pole and is used as […]
The ERITECH® brand of solar bonding lugs from ERICO are designed to bond the frames and mounting structures of solar photovoltaic systems in accordance with NEC® requirements. These lugs are […]
The unique design of the Earth Rod Seal Kits prevents ground water from entering the earth pit and reduces pressure on the cover and inner chamber. Waterproofing is achieved by […]
TGB & TMGB Ground Busbars meet specifications of ANSI®/TIA®/EIA® J-STD-607-A and conform to BICSI® recommendations.
The new EK16 and EK17 Direct-Burial Ground Clamp from ERICO® is a time-saving, cost-effective versatile product that combines four clamps into one. This unique bronze-alloy grounding clamp with bronze screws […]
Copper theft has become a significant problem at many wireless telecommunications sites. Ground bars, conductors and cables are often targeted by thieves, leaving behind a compromised system which is vulnerable […]
The 2005 NEC® standard requires bonding to concrete encased electrodes (rebar) in grounding systems. In some states, the Authorities Having Jurisdiction (AHJ) have taken this requirement a step further and […]
The Universal Pedestal Clamp, part of the ERITECH® line from ERICO, allows for fast, simple and economical field construction of mesh bonding network (MBN), such as supplementary bonding grids, and […]
WAPP offers ERITECH® Arc Weldable Bonds.
ERITECH® brand of CWP grounding clamps are listed for connecting HEX Fittings on CSST systems. ERICO® has developed a range of CWP Grounding Clamps which help minimize the possibility of […]
ERITECH Chemical Ground Electrode System provide a low-impedance ground in locations of high soil resistivity. Together with GEM as backfill, the system dissipates lightning energy and other dangerous electrical fault […]
The handheld ERITECH® EST401 Ground Resistance Tester measures ground rod and small grid resistance in any season without the use of auxiliary ground rods. The tester can measure the resistance […]
In addition to CADWELD® exothermic connections, ERICO also offers mechanical connectors for applications that do not warrant a welded connection. Bronze & Zinc Water Pipe Clamps is ideal for connecting […]
Installing eight-foot-long ground rods can be challenging if purpose-designed driving equipment is not available. Installers stand on ladders, truck beds or use other difficult methods to drive ground rods into […]
Erico offers ERITECH® Inspection Wells, available in Polymer Concrete or High Density Polyethylene
ERICO introduces the ERITECH® LP302 universal air terminal base. The new Series 302 replaces a number of previous models, providing the lightning protection installer with one product for either adhesive […]
Official ERICO copper ground rod distributor in Perth, WA. In a grounding system, the ground electrode provides the physical connection to the earth and is the instrument used to dissipate […]
The new ERITECH® Mechanical Signal Reference Grid system allows for fast, simple and economical field construction of wire signal reference grids used in computer room grounding. In addition to cross-wire […]
Earth Bonding is generally used to reduce the risk of electric shocks if someone was to touch two separate metal objects that are live. Earth bonding connects bonding conductors between […]
WAPP offers a range of galvanized ground rod and accessories.
Fence and Gate Post Clamps, part of the ERITECH® line of Facility Electrical Protection products from ERICO®, help protect your valuable facilities, equipment and personnel when lightning or other transient […]
ERITECH® brand of ground plates from ERICO provide a large surface area to dissipate current into the ground. They are made from high-conductivity copper sheets and are available with pigtail […]
Proper bonding is essential to create an equipotential plane between service grounds and equipment during fault and transient conditions. This equipotential plane provides a near zero voltage differential and serves […]
The patented ERITECH HAMMERLOCK grounding connector connects the grounding conductor to the ground rod, and is designed to withstand ground fault currents and lightning transients. ERITECH HAMMERLOCK’s mechanically rugged design […]
The range of ground resistance testers offered by ERICO are lightweight and portable for ease of use in the field. Their large display shows required test connections and features a […]
The SP58 Stainless Steel Ground Rod Clamp, part of the ERITECH® line of products from ERICO, is made from a non-rigid stainless steel metal strip, which will not crack when […]
ERICO prefabricated wire mesh mats are convenient, efficient and economical for safe grounding in high voltage installations and wherever large area equipotential grounds are required.
Critical ground terminations require a high level of security to ensure their integrity under all conditions. In addition to this, regular maintainance of these terminations is often a requirement of […]